accessories

This product can be used as a pelmet or as a modern cornice

A modern curved cornice/light pelmet for use with the radius feature ends.

28mmx50mm/337mm long x 103mm wide, with a 64mm outer radius

Veneered MDF plinth. Finished on face and 2 long edges.

A modern curved cornice/light pelmet for use with the small curved door.

A modern curved plinth for use with the small curved door.

Curved 'S' shaped plinth for use with either 'S' shaped doors or drawer fronts. Available in American Walnut.

150mm x 16mm x 800mm

Finished on front side and matt lacquered on reverse. Top and bottom edges are not edgebanded.

Also available: -
* curved cornice/light pelmet
* curved plinth

Curved 'S' shaped plinth for use with 1000mm 'S' drawer fronts. Available in American Walnut.

150mm x 16mm x 1000mm

Finished on front side and matt lacquered on reverse. Top and bottom edges are not edgebanded.

Also available: -
* curved cornice/light pelmet
* curved plinth

A jig to assist in producing carcases when using American Walnut curved doors

A jig to assist in producing carcases when using, American Walnut s-shaped doors.

A flexible laminate which can be used when creating a curved plinth. The shaped plinth is made from a suitable material then the laminate, which has 2 strips of double sided tape on the reverse, is applied. 2450mm long x 150mm high x 1.5mm thick.

This 'S' shaped plinth is for use with the 'S' shaped doors or drawer fronts.

150mmx16mmx1200mm, with a 645/537mm radius

Finished with a matching veneer on the front side and a balancing veneer on the reverse.

A curved plinth for use with the curved base unit doors.

150mm x 16mm/531mm long x 386mm wide, with a 313 outer/297mm inner radius with straight ends
The length can be reduced by 15mm to allow for a shallower carcase

Finished on the front side with a matching veneer, and with a balancing veneer on the reverse.

NOTE - The plinth should be set 44mm back from the carcass

Corner post supplied as 2 sections. Each piece has one long edge with a profile to match the doors. The short edges are finished.

70mm wide x 715mm high x 22mm deep

Plate rack made from solid timber spindles and rails. 1200mm long but can be cut down. Features 25 x 10mm diameter dowels at 47mm centres, set between 18mm top and bottom rails.

1200mm long x 336mm high x 18mm deep.

Spice drawer packs are available for use with 500mm cabinets in 15 or 18mm board. The packs consist of the following: -
3 x Drawer fronts, 163mm wide x 139mm high
3 x Drawer boxes, 141mm wide x 250mm deep x 105mm high (sides)/
100mm high (ends)
2 x Drawer guides, 18mm wide x 200mm deep x 21mm high

The drawer guides are reversible to suit 15 or 18mm carcase material.

End panel, profiled front edge, finished face, reverse and 3 square edges 2400x610x28mm

End panel, finished on face, reverse and 4 square edges 2400x650x18mm

Flying shelf, profiled front edge, finished on face, reverse and 3 square edges, 2400x325x28mm

A roll of pre-glued melamine edging tape 100m long x 22mm wide.

as above but 100mm long x 23mm wide x 2mm deep

PVC edgings are primed for glue. Please note the following glues are suitable for Raukantex edging:

When manually applying Raukantex edging the following glues are suitable:
Dorus Ltd, product = LD 084.
Rakoll Ltd, Product = RAKOLLIT 77 & hardener.

150mm long x 23 mm wide x 0.8mm deep