accessories

Traditional cornice made from veneer wrapped MDF

3050mm long x 78mm wide x 69mm high (when fitted).

A shaped base section available for use with the cornice to offer an alternative chunky look. Made from veneer wrapped MDF.

Dimensions of base section: 3050mm long x 72mm wide x 47mm high.

A castellated base section available for use with the cornice to offer an alternative chunky look. Made from veneer wrapped MDF.

Dimensions of base section: 3050mm long x 72mm wide x 47mm high

Handing is determined by the end of the unit it is to be used on (as you look at it).

95mm wide x 150mm long x 114mm high.

as above but right handed

Lighting pelmet made from veneer wrapped MDF.

3050mm long x 50mm highx 18mm thick.

A castellated lighting pelmet made from veneer wrapped MDF.

3050mm long x 50mm highx 18mm thick.

Plinth made from veneer wrapped MDF. 3050mm long x 150mm high x 16.5mm thick.

Shaped plinth made from veneer wrapped MDF.

3050mm long x 160mm high x 25.5mm thick

Traditional cornice specifically for use with Eden curved doors when in a wall unit application. Manufactured using plywood.
Total width 78mm
Total height 69mm (when fitted)
Please note there is an accepted +/- tolerance of up to 3% on this product.
This item is handed, as it is oversized by 15mm on one end, allowing it to be scribed into a wall.
Note - this item is not designed for use with the cornice base.

as above but right handed

Plywood veneer pelmet for use with the Eden curved doors, (note -the curved option is not available in the castellated style).
50mm high and 18mm deep when fitted, with a 1.5x1.5mm bevel between finished edges.

Please note there is an accepted +/- tolerance of up to 3% on this product.
This item is handed, as it is oversized by 15mm on one end, allowing it to be scribed into a wall.

as above but right handed

Veneered plywood curved plinth for use with the curved doors. Finished on face and 2 long edges

Corner post supplied as 2 sections, both at 715mm high x 71mm wide x 20mm thick. Each piece has one long edge with a profile to match the doors. The short edges are finished.

Bottle rack which has 13 grooves for bottles and can be cut to size.

1200mm long x 58mm high x 20mm thick.

91mm between centre of each groove.

Plate rack 1200mm long x 336mm high x 21mm thick. Rack has 25 x 10mm spindles at 48mm centres.

Framed wall quadrant. 720mm high x 320mm wide x 320mm deep. Supplied in component form.

Framed wall quadrant. 900mm high x 320mm wide x 320mm deep. Supplied in component form.

Unhanded, framed floor quadrant. 720mm high x 320mm wide x 580mm deep. Supplied in component form.

Corner moulding that can be used with Eden framed quadrants. Supplied as pairs, 1LH & 1RH.

150mm high x 120mm wide x 18mm thick

A cooker canopy, 800mm wide x 775mm high x 474mm deep. The front of the canopy has a 797mm x 463mm fascia in the same style as the doors. Supplied in component form.

Tongued & grooved canopy: -
Width: 1000mm (can be cut down to 800mm)
Height: 610mm (can be reduced by up to 170mm)
Hood depth: 176mm (plus 18mm backboard)
Total depth: 484mm

Spice drawer packs are available for use with 500mm cabinets in 15 or 18mm board. The packs consist of the following: -
* 3 x Drawer fronts, 163mm wide x 139mm high
* 3 x Drawer boxes, 141mm wide x 250mm deep x 105mm high (sides)/
100mm high (ends)
* 2 x Drawer guides, 18mm wide x 200mm deep x 21mm high

The drawer guides are reversible to suit 15 or 18mm carcase material.

Pilaster is 890mm high x 50mm wide x 100mm deep.
Spacer is 890mm high x 50mm wide x 30mm deep.

A feature end panel pack consists of a radiused (25mm rad) solid timber pilaster and an mdf spacer. An 18mm end panel is added (not provided) to give a chunky, rounded finish to a run of units.

Pilaster is 1210mm high x 50mm wide x 100mm deep.
Spacer is 1210mm high x 50mm wide x 30mm deep.

A feature end panel pack consists of a radiused (25mm rad) solid timber pilaster and an mdf spacer. An 18mm end panel is added (not provided) to give a chunky, rounded finish to a run of units.

Pilaster is 2120mm high x 50mm wide x 100mm deep.
Spacer is 2120mm high x 50mm wide x 30mm deep.

A feature end panel pack consists of a radiused (25mm rad) solid timber pilaster and an mdf spacer. An 18mm end panel is added (not provided) to give a chunky, rounded finish to a run of units.

Wall pilaster. 775mm high x 75mm wide x 100mm deep.

Wall pilaster. 955mm high x 75mm wide x 100mm deep

Floor pilaster. 890mm high x 75mm wide x 100mm deep.

Dresser pilaster. 1210mm high x 75mm wide x 100mm deep.

Pilaster. 2120mm high x 75mm wide x 100mm deep.

A decorative column which can be used as an attractive feature, or to fill those awkward spaces. 890x65x65mm.

A side mantel piece with features to co-ordinate with the door. A top mantel piece is also available.

1500mm long x 250mm wide x 20mm thick.

Note: These mantels have radiused edges and may require mitre joints

A top mantel piece with features to co-ordinate with the door. A side mantel piece is also available.

1500mm long x 250mm wide x 20mm thick.

Note: These mantels have radiused edges and may require mitre joints.

corbel 245mm high x 188mm wide x 137mm deep

Traditionally styled corbels offer decorative focal points. Taditionally used to enhance archways these decorative supports can also be used as shelf supports, mantle supports or under beams and worksurfaces.

Traditionally styled corbel and bracket accessories offer decorative focal points. Taditionally used to enhance archways these decorative supports can also be used as shelf supports, mantle supports or under beams and worksurfaces

Shelf support, solid timber, finished on both faces. Supplied singularly. 190mm high x 137mm wide x 18mm thick.

Corner moulding. Supplied as pairs. 150mm high x 120mm wide x 18mm thick.

Solid timber shelf edging. 2400mm long x 18mm wide x 7mm thick

Veneered end panel with profiled edge,finished on one face, 100mm of reverse and 3 square edges, 2400x650x28mm.

End panel finished on face and 4 square edges, sealed on reverse, 2400x650x18.

Tongue and groove end panel, finished on face, 100mm of reverse (plain matching), and 4 square edges, 2400x650x18mm

Veneered flying shelf with profiled front edge, (10mm radius), finished on face, reverse and 3 square edges, 2400x325x28mm.