accessories

Cornice made from pvc foil wrapped MDF

Total width 130mm (overhang 80mm)
Height when fitted 37mm

castellated section for use with the traditional cornice.
Length: 3050 mm
Width: 50 mm
Height: 22 mm
Castellated section dimensions: 5mm, 12mm, 5mm, 12mm etc.

A lighting pelmet: -
Length: 3050 mm
Depth: 19 mm
Height: 50 mm

A castellated lighting pelmet: -
Length: 3050 mm
Height: 60 mm
Thickness: 18 mm

Plinth made from foil wrapped mdf, 3m x 150mm high x 16mm thick. It is wrapped around both long edges.

A decorative moulded plinth made from foil wrapped mdf. 3050mm x 160mm high x 25mm thick, it is wrapped around both long edges. Can be fitted by adding a baton to the back of the plinth and secured by screwing through the carcase base in to the baton.

Corner post supplied as 2 sections. Each piece has one long edge with a profile to match the doors. The short edges are finished.

Corner post, 715x70x22mm

Supplied ready to assemble, quadrant has decorative frame.

Fittings Pack Includes:
20 x DW2
4 x LAM10
6 x C15/18ZA
6 x D34/E5ZP

A pair of decorative corner mouldings rebated to suit the framed wall quadrants. 117x147x18mm

A tongue & grooved cooker canopy
Total Width: 1000 mm (can be cut down to 800mm wide)
Total Height: 790 mm (can be reduced by maximum 165mm)

Bottle rack profile, 1200mm long and can be cut to size. Has 13 grooves for bottles.

1200x58x20mm.

Plate rack made from solid timber spindles and rails. 1200mm long but can be cut down. Features 25 x 10mm diameter dowels at 47mm centres, set between 18mm top and bottom rails.

1200 x 336 x 18mm

Spice drawer packs are available for use with 500mm cabinets in 15 or 18mm board. The packs consist of the following: -
* 3 x Drawer fronts, 163mm wide x 139mm high
* 3 x Drawer boxes, 141mm wide x 250mm deep x 105mm high (sides)/
100mm high (ends)
* 2 x Drawer guides, 18mm wide x 200mm deep x 21mm high

The drawer guides are reversible to suit 15 or 18mm carcase material.

This range of pilasters are 100mm wide x 100mm deep and are finished on the front and 2 sides.

This range of pilasters are 100mm wide x 100mm deep and are finished on the front and 2 sides.

This range of pilasters are 100mm wide x 100mm deep and are finished on the front and 2 sides.

This range of pilasters are 100mm wide x 100mm deep and are finished on the front and 2 sides.

A decorative mantel side panel. 1500mm long x 250mm wide, it can be reduced by up to 481mm at one end and 200mm at the other

A decorative mantel top panel. 1500mm long x 250mm wide, it can be reduced by up to 295mm at each end.

Shaped shelf support, 190mm high x 137mm deep x 18mm thick.

A pair of decorative corner moudings suitable for open units. 120x150x18mm.

Foil wrapped gallery rail 1500mm x 51mm x 28mm

End panel finished on face, reverse and 4 square edges, 2400x650x18mm.

This end panel is supplied with 3 lengths of unglued edging tape 2.4mx32mm.

Tongue and groove end panel, finished on face, reverse (plain) and 2 long edges, 2400x650x18mm.

Shaped end panel with tongue & groove, finished on face, reverse (reverse T& G) and 4 square edges, 1400x325x18mm.
The length of the end panel could be reduced by up to 965mm.

Tongue and groove flying shelfl, finished on face, reverse (plain) and 2 long edges, 2400x325x18mm

A roll of pre-glued melamine edging tape 100m long x 22mm wide.

PVC edgings are primed for glue. Please note the following glues are suitable for Raukantex edging:

When manually applying Raukantex edging the following glues are suitable:
Dorus Ltd, product = LD 084.
Rakoll Ltd, Product = RAKOLLIT 77 & hardener.

150mm long x 23 mm wide x 0.8mm deep

as above but 100mm long x 23mm wide x 2mm deep