accessories

Traditional cornice made from veneer wrapped MDF.

3050mm long x 78mm wide x 69mm high (when fitted).

A shaped base section available for use with the cornice to offer an alternative chunky look. Made from veneer wrapped MDF.

Dimensions of base section: 3050mm long x 72mm wide x 47mm high.

A castellated base section available for use with the cornice to offer an alternative chunky look. Made from veneer wrapped MDF.

Dimensions of base section: 3050mm long x 72mm wide x 47mm high.

A chunky corner block which can be used on top of a wall unit or dresser, above a radius feature end. The curved corner blocks are available in left hand or right hand options and should be used in conjunction with the cornice and cornice base. Handing is determined by the end of the unit it is to be used on (as you look at it).

95mm wide x 150mm long x 114mm high.

As above but right hand

A castellated ighting pelmet made from veneer wrapped MDF.

3050mm long x 50mm highx 18mm thick.

Lighting pelmet made from veneer wrapped MDF.

3050mm long x 50mm highx 18mm thick.

Plinth made from veneer wrapped MDF. 3050mm long x 150mm high x 16.5mm thick.

Shaped plinth made from veneer wrapped MDF.

3050mm long x 160mm high x 25.5mm thick.

Corner post supplied as 2 sections, both at 715mm high x 70mm wide x 20mm thick. Each piece has one long edge with a radius profile to match doors. The short edges are finished

Framed wall quadrant. 720mm high x 320mm x 320mm. Supplied in component form.

Framed wall quadrant. 900mm high x 320mm x 320mm. Supplied in component form.

Unhanded, framed floor quadrant. 720mm high x 320mm wide x 580mm deep. Supplied in component form.

Corner moulding that can be used with Bede quadrants. Supplied as pairs, 1left hand & 1right hand

A cooker canopy, 800mm wide x 775mm high x 474mm deep. The front of the canopy has a 797mm x 463mm fascia in the same style as the doors. Supplied in component form

Tongued & grooved canopy: -
Width: 1000mm (can be cut down to 800mm)
Height: 610mm (can be reduced by up to 170mm)
Hood depth: 176mm (plus 18mm backboard)
Total depth: 484mm

Bottle rack which has 13 grooves for bottles and can be cut to size.

1200mm long x 58mm high x 20mm thick.

91mm between centre of each groove.

Plate rack 1200mm long x 336mm high x 21mm thick. Rack has 25 x 10mm spindles at 48mm centres.

Spice drawer packs are available for use with 500mm cabinets in 15 or 18mm board. The packs consist of the following: -
* 3 x Drawer fronts, 163mm wide x 139mm high
* 3 x Drawer boxes, 141mm wide x 250mm deep x 105mm high (sides)/
100mm high (ends)
* 2 x Drawer guides, 18mm wide x 200mm deep x 21mm high

The drawer guides are reversible to suit 15 or 18mm carcase material.

A feature end panel pack consists of a radiused (25mm rad) solid timber pilaster and an mdf spacer. An 18mm end panel is added (not provided) to give a chunky, rounded finish to a run of units.

The end panel is fixed to the pilaster and spacer by screwing from the rear and then the assembly can be fitted to the unit by screwing from inside the carcase. Screws are not supplied.

as above but to fit dresser

1210 high x 50mm wide x100mm deep

as above but taller size

2120 high x 50mm wide x 100mm deep

Wall pilaster, 775mm high x 50mm wide x 60mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

Wall pilaster, 955mm high x 50mm wide x 60mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

Floor pilaster, 890mm highx50mm widex85mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

A decorative column which can be used as an attractive feature, or to fill those awkward spaces. 890x65x65mm.

Dresser pilaster. 1210mm high x 75mm wide x 100mm deep.

Pilaster. 2120mm high x 75mm wide x 100mm deep.

A side mantel piece with features to co-ordinate with the door.

1500mm long x 250mm wide x 20mm thick.

Note: These mantels have radiused edges and may require mitre joints.

A top mantel piece with features to co-ordinate with the door

1500mm long x 250mm wide x 20mm thick.

Note: These mantels have radiused edges and may require mitre joints.

Shelf support, solid timber, finished on both faces. Supplied singularly. 190mm high x 137mm wide x 18mm thick.

Corner moulding. Supplied as pairs. 150mm high x 120mm wide x 18mm thick.

Solid timber shelf edging. 2400mm long x 18mm wide x 7mm thick.

Veneered end panel with profiled edge,finished on one face, 100mm of reverse and 3 square edges, 2400x650x28mm

End panel finished on face and 4 square edges, sealed on reverse, 2400x650x18.

Veneered flying shelf with profiled front edge, (10mm radius), finished on face, reverse and 3 square edges, 2400x325x28mm.

Tongue and groove end panel, finished on face, 100mm of reverse (plain matching), and 4 square edges, 2400x650x18mm.

A roll of pre-glued melamine edging tape 100m long x 22mm wide.

Unglued veneer edging 3mx32mmx0.6mm

PVC edgings are primed for glue. Please note the following glues are suitable for Raukantex edging:

When manually applying Raukantex edging the following glues are suitable:
Dorus Ltd, product = LD 084.
Rakoll Ltd, Product = RAKOLLIT 77 & hardener.

150mm long x 23 mm wide x 0.8mm deep

as above but 100mm long x 23mm wide x 2mm deep

corbel 245mm high x 188mm wide x 137mm deep

Traditionally styled corbels offer decorative focal points. Taditionally used to enhance archways these decorative supports can also be used as shelf supports, mantle supports or under beams and worksurfaces.

Traditionally styled brackets offer decorative focal points. Taditionally used to enhance archways these decorative supports can also be used as shelf supports, mantle supports or under beams and worksurfaces