accessories

Veneered MDF cornice.
Total width 130mm (overhang 80mm)
Height when fitted 37mm

A curved corner block which can be used on top of a wall unit or dresser, above a radius feature end.

The end of the unit that it is to be used on (as you look at it) determines handing.

135mm wide x 180mm long x 37mm high.
Projection: 85mm (distance stands out from radius feature end)

As above but for right hand (as you look at it)

This curved cornice is specifically for use with the curved door when used in a wall application. Manufactured using plywood.
Total width 130mm (overhang 80mm)
Height when fitted 37mm
Please note there is an accepted +/- tolerance of up to 3mm on this product.
This item is handed, as it is oversized by 15mm on one side, allowing it to be scribed to a wall.

as above but for right hand

Veneer wrapped MDF pelmet which can also act as a modern cornice or pilaster. Finished 3 sides.
When fitted as pelmet 50mm high x 28mm deep. Has 1.5 x 1.5 mm bevel between finished edges.

Plywood veneer pelmet for use with the curved doors.
50mm high and 28mm deep when fitted, with a 1.5x1.5mm bevel between finished edges.
Please note there is an accepted +/- tolerance of up to 3mm on this product.
This item is handed, as it is oversized by 15mm at one end, allowing it to be scribed to a wall.

As above but for right hand

Veneered MDF plinth. Finished on face and 2 long edges.

Veneered plywood curved plinth for use with the curved doors. Finished on face and 2 long edges.

Corner post supplied as 2 sections. Each piece has one long edge with a profile to match the doors. The short edges are finished.

Corner post, 715x70x20mm

Modern style plate rack with 25 lightweight stainless steel effect tubes. Each tube is 14mm dia., and fitted at 48mm centres, with an exposed height of 298mm.

Plate rack made from solid timber spindles and rails. 1200mm long but can be cut down. Features 25 x 10mm diameter dowels at 47mm centres, set between 18mm top and bottom rails.

1200 x 336 x 18mm.

Modern style bottle rack with lightweight stainless steel effect tubes. Each tube is 14mm dia., and fitted at 80mm centres, with an exposed height of 390mm.

Bottle rack profile. Solid timber 1200mm long and can be cut to size. Product has 13 grooves for bottles.

1200x58x20mm

Quadrants made from veneered panels. The top, base and side boards are 28mm thick, while the shelves are 18mm. Supplied ready to assemble.

As above but to fit a 900mm high cabinet

as above but to fit base unit

800mm wide cooker canopy. The size of the fascia used on the canopy is 797mm wide x 463mm high and matches the doors of the range. Supplied ready to assemble.

The Broadoak spice drawer fronts feature an elliptical finger hole for easy opening. The reverse side is solid.

Spice drawer packs are available for use with 500mm cabinets in 15 or 18mm board. The packs consist of the following: -
* 3 x Drawer fronts, 163mm wide x 139mm high
* 3 x Drawer boxes, 141mm wide x 250mm deep x 105mm high (sides)/
100mm high (ends)
* 2 x Drawer guides, 18mm wide x 200mm deep x 21mm high

The drawer guides are reversible to suit 15 or 18mm carcase material.

A feature end panel pack consists of a radiused (25mm rad) solid timber pilaster and an mdf spacer. An 18mm end panel is added (not provided) to give a chunky, rounded finish to a run of units.

The end panel is fixed to the pilaster and spacer by screwing from the rear and then the assembly can be fitted to the unit by screwing from inside the carcase. Screws are not supplied.

as above but to fit dresser

1210 high x 50mm wide x100mm deep

as above but taller size

2120 high x 50mm wide x 100mm deep

Wall pilaster, 775mm high x 50mm wide x 60mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

Wall pilaster, 955mm high x 50mm wide x 60mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

Floor pilaster, 890mm highx50mm widex85mm deep.

50mm wide pilaster, plain in style with chamfered edges. The pilasters are finished on 3 sides (front and 2 sides).

End panel, finished on face, 100mm on reverse and 4 square edges, 2400x650x28mm

End panel finished on face and 4 square edges, sealed on reverse, 2400x650x18.

Tongue & grooved, veneered end panel is finished on 1 face and 4 square edges,2400x650x18mm.

Flying shelf , finished on face, reverse and 4 square edges, 2400x325x28mm.

A roll of pre-glued melamine edging tape 100m long x 22mm wide.

Unglued veneer edging 3mx32mmx0.6mm

PVC edgings are primed for glue. Please note the following glues are suitable for Raukantex edging:

When manually applying Raukantex edging the following glues are suitable:
Dorus Ltd, product = LD 084.
Rakoll Ltd, Product = RAKOLLIT 77 & hardener.

150mm long x 23 mm wide x 0.8mm deep

as above but 100mm long x 23mm wide x 2mm deep